苹果版时时红包

Your current location : Home >> Products >> Construction Machinery Series >> Concrete spray pipe
  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.

  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.

  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.

  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.

  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.

  • Engineering truck pump tube

    1. The rubber conveying hose at the end of the concrete pump truck. The technical parameters of the pressure are requested. The user must recognize the 125A ordinary type. The use pressure should not exceed 4MPa, the bending radius should not be less than 1M, and each piece of concrete should not be less than 10,000 cubic meters in normal use. ability. Second, 150A ordinary type The working pressure should not exceed 3.5MPa, the bending radius is not less than 1M, and the normal conveying capacity of each concrete is not less than 10,000 cubic meters. Third, the 125AB high-pressure steel curtain use pressure should not exceed 10MPa, the bending radius is not less than 1M, in normal use, each one is not less than 12,000 cubic meters of concrete transport capacity. 4. The working pressure of 150AB high pressure steel curtain shall not exceed 9.5MPa, the bending radius shall not be less than 1M, and the conveying capacity of each concrete shall not be less than 12000 cubic meters in normal use. Fifth, the operator should do a good job of standardizing the work. Operators who do not have the standard must not be employed. When connecting the ends, prevent the pipe card from being not tightened, the seal ring is damaged, and the seal ring has not been added. Steel pipes, ordinary hoses, and modern hoses can only be used as end outlets, and should not be used instead of connecting elbows and straight pipes. Use at your own risk. 6. When the pipe is blocked, it must be handled after normal use, such as piled up at the exit, piled up at the exit of the silo, mixed silo-type plugged pipe, pipe-type slurry plugged pipe, intermittently over-type plugged pipe, pipe gray skin accumulation type plugged pipe , Concrete mortar plugging tube, concrete plugging tube, additive plugging tube, S-type conveying tube plugging, external mixed extremely hot plugging, external temperature extremely cold plugging, air backlogging plugging, Pipe diameter variation type plugging, aggregate oversized plugging, flow out of control type plugging, etc. If the abnormal phenomenon is not ruled out in time, the hose will be deformed due to heating. The aggregate in the pipe will collide and squeeze and stroke the inner wall, which will cause the hose to bulge at the accumulation site, especially the 3.5cm diameter aggregate. The longer the time, the greater the harm, and the less frequent the collision of the inner wall of the hose, the greater the penetrability, and finally the skinning phenomenon at the drum will appear from small to large, such as the flange will also have the same consequences (tube The head flange is bonded off). However, as long as the correct state of all aspects is selected, it will surely reach the best situation for delivery and reduce unnecessary losses.